AVR ATmega32 Mini Development Board – Interfacing μRFID (EM-18 Compatible)

AVR ATmega32 mini development board has on-board connector for interfacing microRFID reader. The reader reads the 10-byte address of a card within its range. Communication between μRFID reader & controller is via USART module. The sample code given below is written to display the address of the card on LCD.

The locations of jumpers and microRFID reader slot on the mini development board are shown in the pictures given below.

Note: Keep the jumpers J1, J2, J13 & J14 open while using RFID reader.

Schematic

Sample Code

/*************************************************************************************
                                   HEADER FILES
**************************************************************************************/
#define F_CPU 8000000L
#include<avr/io.h>                 /* Header File Inclusion                          */
#include<util/delay.h>             /* Delay File Inclusion                           */

/*************************************************************************************
                          	FUNCTION DECLARATIONS
**************************************************************************************/
void Display(char loc, const char *LCD);
void Command(unsigned char cmd);
void Data(unsigned char dat);

/*************************************************************************************
                           	VARIABLE DECLARATIONS
**************************************************************************************/
volatile char Rec_Array[17];
volatile char j;
int i;

/*************************************************************************************
                                 MAIN FUNCTION
**************************************************************************************/
int main()
{
 DDRB = 0xFF;                      /* LCD data lines                                 */
 DDRD = 0X62;                      /* PORTD 2nd Is set Output(RD1=1)and RD2=0 & set  
                                      input Controllines(RS(PD5),RW(GND),EN(PD6)     */
 PORTD = 0x1C;
 UCSRA = 0X00;                     /* Clears TXC & RXC Flag Bit                      */
 UCSRB = 0X18;                     /* Transmission Enabling (TXEN=1)                 */														
 UCSRC = 0X86;                     /* URSEL=1,UMSEL=0,UCSZ1=1,UCSZ0=0                */
 UBRRL = 51;                       /* Serial Baudrate=9600                           */

 _delay_us(15);                    /*  Minimum Delay To Power On LCD To Recieve Mode */
 Command(0x30);                    /*  LCD Specification Cmdmands                    */
 _delay_us(5); 
 Command(0x30);                    /*  LCD Specification Cmdmands                    */
 _delay_us(2); 
 Command(0x30);                    /*  LCD Specification Cmdmands                    */
 Command(0x38);                    /*  LCD Double Line Display Cmdmand               */
 Command(0x06);                    /*  LCD Auto Increment Location Address Cmdmand   */
 Command(0x0C);                    /*  LCD Display ON Cmdmand                        */
 Command(0x01);                    /*  LCD Display Clear Cmdmand                     */
 _delay_us(1200); 
 Display(0x80, "RFID Test...");

 while(1)
 {
  while((UCSRA & 0X80)!=0X80);     /* Reading data fom buffer                        */
  Rec_Array[j]=UDR;                /* RFID card no stored into array                 */
  j++;                             /* increment array index                          */
  if (j==12)
  {                                /* checking 12 digit no rx complete               */
   Rec_Array[j]='\0';              /* adding null character                          */
   j=0; 
   Command(0x01);
   _delay_us(1000); 
   Command(0xC3);
   for(i=0;i<=11;i++)              /* display rfid number                            */
   {
    Data(Rec_Array[i]);            /*  LCD display function                          */
   }
  }
 }
}

/*************************************************************************************
* Function    : Command                                                              *
*                                                                                    *
* Description : Function to send a command to LCD                                    * 
*                                                                                    *
* Parameters  : cmd - command to be sent                                             *
**************************************************************************************/
void Command(unsigned char cmd)
{
 PORTD |= 0X40;                    /* contol line RS-0(cmd register),R/W-GND(write),
                                      E-1(enable)                                    */
 PORTB  = cmd;                     /* command loaded to data port                    */
 _delay_us(50);                    /* Minimun Delay For Hold On Data                 */
 PORTD  = 0X00;                    /* contol line RS-0(cmd register),R/W-GND(write),
                                      E-0(enable)                                    */
}

/*************************************************************************************
* Function    : Data                                                                 *
*                                                                                    *
* Description : Function to display data on LCD                                      *
*                                                                                    *
* Parameters  : dat - data to be displayed                                           *
**************************************************************************************/
void Data(unsigned char dat)
{
 PORTD |= 0X60;                    /* contol line RS-1(data register),
                                      R/W - GND(write), E-1(enable)                  */
 PORTB  = dat;                     /* data loaded to data port                       */
 _delay_us(50);                    /* Minimun Delay For Hold On Data                 */
 PORTD  = 0X00;                    /* contol line RS-0(data register),
                                      R/W - GND(write), E-0(enable)                  */
}

/*************************************************************************************
* Function    : Display                                                              *
*                                                                                    *
* Description : Function to display string in LCD                                    *
*                                                                                    *
* Parameters  : loc - location                                                       * 
*               LCD - String to be displayed                                         *
**************************************************************************************/
void Display(char loc, const char *LCD)
{
 Command(loc);                    /* Address of location to display data             */
 while(*LCD!='\0')                /* Check for termination character                 */	
 {	
  Data(*LCD);                     /* Display the character on LCD                    */	
  LCD++;                          /* Increment the pointer                           */
 }
}
/*************************************************************************************
                           	   END OF PROGRAM
**************************************************************************************/

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

/*************************************************************************************

HEADER FILES

**************************************************************************************/

#define F_CPU 8000000L

#include<avr/io.h> /* Header File Inclusion */

#include<util/delay.h> /* Delay File Inclusion */

/*************************************************************************************

FUNCTION DECLARATIONS

**************************************************************************************/

void Display(char loc, const char *LCD);

void Command(unsigned char cmd);

void Data(unsigned char dat);

/*************************************************************************************

VARIABLE DECLARATIONS

**************************************************************************************/

volatile char Rec_Array[17];

volatile char j;

int i;

/*************************************************************************************

MAIN FUNCTION

**************************************************************************************/

int main()

{

DDRB = 0xFF; /* LCD data lines */

DDRD = 0X62; /* PORTD 2nd Is set Output(RD1=1)and RD2=0 & set

input Controllines(RS(PD5),RW(GND),EN(PD6) */

PORTD = 0x1C;

UCSRA = 0X00; /* Clears TXC & RXC Flag Bit */

UCSRB = 0X18; /* Transmission Enabling (TXEN=1) */

UCSRC = 0X86; /* URSEL=1,UMSEL=0,UCSZ1=1,UCSZ0=0 */

UBRRL = 51; /* Serial Baudrate=9600 */

_delay_us(15); /* Minimum Delay To Power On LCD To Recieve Mode */

Command(0x30); /* LCD Specification Cmdmands */

_delay_us(5);

Command(0x30); /* LCD Specification Cmdmands */

_delay_us(2);

Command(0x30); /* LCD Specification Cmdmands */

Command(0x38); /* LCD Double Line Display Cmdmand */

Command(0x06); /* LCD Auto Increment Location Address Cmdmand */

Command(0x0C); /* LCD Display ON Cmdmand */

Command(0x01); /* LCD Display Clear Cmdmand */

_delay_us(1200);

Display(0x80, "RFID Test...");

while(1)

{

while((UCSRA & 0X80)!=0X80); /* Reading data fom buffer */

Rec_Array[j]=UDR; /* RFID card no stored into array */

j++; /* increment array index */

if (j==12)

{ /* checking 12 digit no rx complete */

Rec_Array[j]='\0'; /* adding null character */

j=0;

Command(0x01);

_delay_us(1000);

Command(0xC3);

for(i=0;i<=11;i++) /* display rfid number */

{

Data(Rec_Array[i]); /* LCD display function */

}

/*************************************************************************************

* Function : Command *

* *

* Description : Function to send a command to LCD *

* *

* Parameters : cmd - command to be sent *

**************************************************************************************/

void Command(unsigned char cmd)

{

PORTD |= 0X40; /* contol line RS-0(cmd register),R/W-GND(write),

E-1(enable) */

PORTB = cmd; /* command loaded to data port */

_delay_us(50); /* Minimun Delay For Hold On Data */

PORTD = 0X00; /* contol line RS-0(cmd register),R/W-GND(write),

E-0(enable) */

}

/*************************************************************************************

* Function : Data *

* *

* Description : Function to display data on LCD *

* *

* Parameters : dat - data to be displayed *

**************************************************************************************/

void Data(unsigned char dat)

{

PORTD |= 0X60; /* contol line RS-1(data register),

R/W - GND(write), E-1(enable) */

PORTB = dat; /* data loaded to data port */

_delay_us(50); /* Minimun Delay For Hold On Data */

PORTD = 0X00; /* contol line RS-0(data register),

R/W - GND(write), E-0(enable) */

}

/*************************************************************************************

* Function : Display *

* *

* Description : Function to display string in LCD *

* *

* Parameters : loc - location *

* LCD - String to be displayed *

**************************************************************************************/

void Display(char loc, const char *LCD)

{

Command(loc); /* Address of location to display data */

while(*LCD!='\0') /* Check for termination character */

{

Data(*LCD); /* Display the character on LCD */

LCD++; /* Increment the pointer */

}

/*************************************************************************************

END OF PROGRAM

**************************************************************************************/

Topics related to AVR ATmega32 Mini Development Board

Resources

Softwares
- AVR Studio
Datasheets
- ATmega32
- MCP 9700
- LM 7805
- LD 1117
- MAX 232
- µRFID Reader (EM-18 compatible)

How to buy?

SupportPlease share your ideas with us, visit our forum for discussion

Leave a Reply Cancel reply