PIC18F4580 – Interfacing POT(ADC)

PIC18F4580 mini development board has a POT connected to pin RA0 i.e, channel0 via jumper J16. Sample code to check the ADC module of PIC18F4550 with potentiometer is given below. The output is displayed on LCD and the variation can be checked with the POT.

Schematic

Note: To use potentiometer, don’t forget to short jumper J16. Leaving it open frees RA0 and it can be used for any other desired purpose.

Sample code

/*************************************************************************
                           HEADER FILES
**************************************************************************/
#include<pic18.h>     

/*************************************************************************
                       FUNCTION DECLARATIONS
**************************************************************************/
void Delay_us(int us);
void Data(int Value);           
void Cmd(int Value);            
void Send2LCD(const char Adr, const char *Lcd);

/*************************************************************************
                       VARIABLE DECLARATIONS
**************************************************************************/ 
int k,ADC_Value;       
char ADC_Array[5];

/*************************************************************************
                           MAIN FUNCTION
**************************************************************************/
void main()                     
{
 TRISA = 0XFF;                  /* Set PORTA as input for channel 0      */
 TRISC = 0X00;                  /* PORTC(control lines) configured as o/p*/
 TRISD = 0X00;                  /* PORTD(data lines) configured as o/p   */
 Delay_us(25);                      
 Cmd(0X30);                     /* LCD Specification Command             */
 Delay_us(25);
 Cmd(0X30);                     /* LCD Specification Command             */
 Delay_us(25); 
 Cmd(0X30);                     /* LCD Specification Command             */
 Delay_us(25); 
 Cmd(0X38);                     /* Double Line Display Command           */
 Cmd(0X06);                     /* Auto Increment Location Address       */
 Cmd(0X0C);                     /* Display ON Command                    */
 Cmd(0X01);                     /* Clear Display Command                 */
 Delay_us(1000);
 Send2LCD(0x80,"ADC Result: ");
 ADCON0 = 0x03;              
 ADCON1 = 0x0d;              
 ADCON2 = 0x80;  
 while(1)
 {
  GO = 1;                       /* Set A/D conversion status bit
                                   (conversion in progress)              */
  while(GO==1);                 /* Wait here until A/D conversion is over*/
  ADC_Value = ADRESH;           /* Copy the 2 bits in ADRESH to ADC_Value*/
  ADC_Value = ADC_Value<<8;     /* Shift it 8 bits to left               */
  ADC_Value = ADC_Value+ADRESL; /* Add left shifted value to ADRESL      */

  for(k=0; k<=3; k++)           /* Convert the result into ASCII         */
  {
   ADC_Array[k]= ADC_Value%10+'0';/* Separate each digit of the integer  */
   ADC_Value   = ADC_Value/10;
  }
  Cmd(0X8C);
  for(k=3; k>=0; k--)
  {
   Data(ADC_Array[k]);          /* Display the result on LCD             */
  }
 }
}

/*************************************************************************
* Function    : Cmd                                                      *
*                                                                        *
* Description : Function to send a command to LCD                        *
*                                                                        *
* Parameters  : Value - command to be sent                               *
**************************************************************************/
void Cmd(int Value)
{
 PORTD = Value;                 /* Write the command to data lines       */
 RC0   = 0;                     /* RS-0(command register)                */
 RC1   = 1;                     /* E-1(enable)                           */
 Delay_us(25);             
 RC1   = 0;                     /* E-0(enable)                           */
}	

/*************************************************************************
* Function    : Data                                                     *
*                                                                        *
* Description : Function to display single character on LCD              *
*                                                                        *
* Parameters  : Value - character to be displayed                        *
**************************************************************************/
void Data(int Value)
{
 PORTD = Value;                 /* Write the character to data lines     */
 RC0   = 1;                     /* RS-1(data register)                   */
 RC1   = 1;                     /* E-1(enable)                           */
 Delay_us(25);             
 RC1   = 0;                     /* E-0(enable)                           */
}

/*************************************************************************
* Function    : Send2LCD                                                 *
*                                                                        *
* Description : Function to display string on LCD                        *
*                                                                        *
* Parameters  : loc - location                                           *
*               String to be displayed                                   *
**************************************************************************/
void Send2LCD(const char Adr, const char *Lcd)
{
 Cmd(Adr);                      /* Address of location to display string */
 while(*Lcd!='\0')              /* Check for termination character       */
 {	
  Data(*Lcd);                   /* Display the character on LCD          */
  Lcd++;                        /* Increment the pointer                 */
 }
}

/*************************************************************************
* Function    : Delay_us                                                 *
*                                                                        *
* Description : Function for 1 microsecond delay                         *
*                                                                        *
* Parameter   : Delay - delay in microseconds                            *
**************************************************************************/
void Delay_us(int us)
{
 us = us>>1;
 while(us!=1)
 us--;
}

/***************************  END OF PROGRAM  ****************************/

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

/*************************************************************************

HEADER FILES

**************************************************************************/

#include<pic18.h>

/*************************************************************************

FUNCTION DECLARATIONS

**************************************************************************/

void Delay_us(int us);

void Data(int Value);

void Cmd(int Value);

void Send2LCD(const char Adr, const char *Lcd);

/*************************************************************************

VARIABLE DECLARATIONS

**************************************************************************/

int k,ADC_Value;

char ADC_Array[5];

/*************************************************************************

MAIN FUNCTION

**************************************************************************/

void main()

{

TRISA = 0XFF; /* Set PORTA as input for channel 0 */

TRISC = 0X00; /* PORTC(control lines) configured as o/p*/

TRISD = 0X00; /* PORTD(data lines) configured as o/p */

Delay_us(25);

Cmd(0X30); /* LCD Specification Command */

Delay_us(25);

Cmd(0X30); /* LCD Specification Command */

Delay_us(25);

Cmd(0X30); /* LCD Specification Command */

Delay_us(25);

Cmd(0X38); /* Double Line Display Command */

Cmd(0X06); /* Auto Increment Location Address */

Cmd(0X0C); /* Display ON Command */

Cmd(0X01); /* Clear Display Command */

Delay_us(1000);

Send2LCD(0x80,"ADC Result: ");

ADCON0 = 0x03;

ADCON1 = 0x0d;

ADCON2 = 0x80;

while(1)

{

GO = 1; /* Set A/D conversion status bit

(conversion in progress) */

while(GO==1); /* Wait here until A/D conversion is over*/

ADC_Value = ADRESH; /* Copy the 2 bits in ADRESH to ADC_Value*/

ADC_Value = ADC_Value<<8; /* Shift it 8 bits to left */

ADC_Value = ADC_Value+ADRESL; /* Add left shifted value to ADRESL */

for(k=0; k<=3; k++) /* Convert the result into ASCII */

{

ADC_Array[k]= ADC_Value%10+'0';/* Separate each digit of the integer */

ADC_Value = ADC_Value/10;

}

Cmd(0X8C);

for(k=3; k>=0; k--)

{

Data(ADC_Array[k]); /* Display the result on LCD */

}

/*************************************************************************

* Function : Cmd *

* *

* Description : Function to send a command to LCD *

* *

* Parameters : Value - command to be sent *

**************************************************************************/

void Cmd(int Value)

{

PORTD = Value; /* Write the command to data lines */

RC0 = 0; /* RS-0(command register) */

RC1 = 1; /* E-1(enable) */

Delay_us(25);

RC1 = 0; /* E-0(enable) */

}

/*************************************************************************

* Function : Data *

* *

* Description : Function to display single character on LCD *

* *

* Parameters : Value - character to be displayed *

**************************************************************************/

void Data(int Value)

{

PORTD = Value; /* Write the character to data lines */

RC0 = 1; /* RS-1(data register) */

RC1 = 1; /* E-1(enable) */

Delay_us(25);

RC1 = 0; /* E-0(enable) */

}

/*************************************************************************

* Function : Send2LCD *

* *

* Description : Function to display string on LCD *

* *

* Parameters : loc - location *

* String to be displayed *

**************************************************************************/

void Send2LCD(const char Adr, const char *Lcd)

{

Cmd(Adr); /* Address of location to display string */

while(*Lcd!='\0') /* Check for termination character */

{

Data(*Lcd); /* Display the character on LCD */

Lcd++; /* Increment the pointer */

}

/*************************************************************************

* Function : Delay_us *

* *

* Description : Function for 1 microsecond delay *

* *

* Parameter : Delay - delay in microseconds *

**************************************************************************/

void Delay_us(int us)

{

us = us>>1;

while(us!=1)

us--;

}

/*************************** END OF PROGRAM ****************************/

Topics related to PIC18F4580 Mini Development Board

Resources

Softwares

Datasheets
- PIC18F4580
- MCP9700
- MAX232
- CP2102
- LM7805
- LD1117
- LCD (16×2)

How to buy?

SupportPlease share your ideas with us, visit our forum for discussion

PIC18F4580 – Switch Interfacing says:

August 7, 2015 at 4:45 am

[…] PIC 18F4580 Mini Development Board – Interfacing POT(ADC) […]

PIC18F4580 – Interfacing μRFID says:

August 21, 2015 at 5:28 am

PIC18F4580 – Interfacing LCD says:

September 29, 2015 at 11:30 am

PIC18F4580 – Serial communication(USART) says:

September 30, 2015 at 6:32 am

PIC18F4580 – Interfacing Servo Motor says:

September 30, 2015 at 8:34 am

PIC18F4580 – Interfacing Temperature Sensor says:

October 6, 2015 at 5:43 am

PIC18F4580 – Interfacing LED says:

October 16, 2015 at 5:32 am

PIC18F4580 – Buzzer Interfacing says:

October 16, 2015 at 5:45 am

PIC18F4580 – Interfacing Servo Motor | Entesla Wiki says:

October 28, 2015 at 4:46 am

PIC18F4580 Mini Development Board – Overview says:

November 23, 2015 at 4:27 am

Leave a Reply Cancel reply